If you find that your Glock 19 rear sight is not aligned properly, you can adjust it yourself with a few simple tools. First, you will need a flat-head screwdriver. Second, you will need to remove the rear sight by loosening the two screws that hold it in place. Once the rear sight is removed, you can use the screwdriver to adjust the windage and elevation screws on the sight. Finally, you can re-install the rear sight by tightening the screws.
Advance Tips: How To Adjust Glock 19 Rear Sight?
If you’re a Glock 19 owner, you know that the rear sight is one of the key components to accuracy. After all, it’s the last thing your eye sees before the bullet leaves the barrel. So, if it’s not properly aligned, your shots will be off target. Fortunately, adjusting the rear sight is a relatively easy process that only requires a few tools and a little bit of know-how.
First, you’ll need a small flathead screwdriver, a punch or small nail, and a hammer. You’ll also need a clean, well-lit work area where you can lay out your Glock 19 and all of your tools.
Once you have everything gathered, begin by removing the magazine and clearing the chamber. Next, take a look at the rear sight. You’ll notice that there are two small Allen screws on either side of the sight. These screws are what you’ll use to adjust the sight.
Using your punch or small nail, tap out the left-hand screw. Be careful not to lose the screw, as it’s easy to misplace in a well-lit room. With the left-hand screw removed, you can now use your flathead screwdriver to adjust the rear sight.
Turn the screwdriver clockwise to move the sight to the right, and counterclockwise to move it to the left. Once you’ve made your adjustments, replace the left-hand screw and tighten it down.
Now it’s time to move to the other side. Again, use your punch or small nail to tap out the right-hand screw. With the screw removed, you can once again use your flathead screwdriver to make adjustments. Remember, turn the screwdriver clockwise to move the sight to the right, and counterclockwise to move it to the left.
Once you’re satisfied with the position of the rear sight, replace the right-hand screw and tighten it down. That’s it! You’ve now successfully adjusted the rear sight on your Glock 19.
Frequently Asked Questions [FAQs]
To adjust the rear sight on your Glock 19, you will need to use a tool to loosen the set screw that holds the sight in place. Once the set screw is loose, you can slide the sight to the left or right to make your adjustments.
In order to adjust the rear sight on your Glock 19, you will need a small Allen wrench or a flathead screwdriver.
The amount that you will need to adjust the rear sight on your Glock 19 will depend on the ammunition that you are using. If you are using factory ammunition, you should only need to make a small adjustment. However, if you are using handloads or other types of ammunition, you may need to make a larger adjustment.
Yes, adjusting the rear sight on your Glock 19 will affect the point of impact. When you make an adjustment to the rear sight, you are effectively moving the point of impact for your gun.
No, it is not difficult to adjust the rear sight on your Glock 19. However, it is important that you take your time and make sure that you do not make any mistakes. Once you have loosened the set screw, you should be able to slide the sight to the left or right without any issue.
Conclusion
Based on the instructions provided, it seems that adjusting the rear sight of a Glock 19 is a relatively simple process. First, remove the magazine and make sure the chamber is empty. Next, use a punch or other tool to drift the rear sight in the direction you want the bullet to impact. Finally, test fire the gun to ensure that the sight adjustment is accurate.
A. Wilcox Head is a lifelong shooter, hunter, and firearms enthusiast. Head grew up in a family where firearms were a way of life, and from an early age, he was taught the importance of firearm safety, accuracy, and proper hunting techniques.
