In order to remove the 10/22 barrel from the rifle, you will need to first remove the magazine and bolt assembly. Next, locate the two pins that secure the barrel to the receiver. These pins are located just above the chamber, on either side of the barrel. Using a punch or other small tool, drive the pins out from left to right. The barrel can now be slid forward and off the receiver.
To reassemble, reverse the process. Slide the barrel back onto the receiver and align the holes for the pins. Insert the pins and tap them into place. Be sure that the pins are flush with the surface of the receiver, or the barrel will not be properly secured.
Advance Tips: How To Remove 10 22 Barrel?

Assuming you would like an article discussing how to remove the barrel from a Ruger 10/22:
The Ruger 10/22 is a .22 caliber semi-automatic rifle that is very popular for both target shooting and small game hunting. The 10/22 has been in production since 1964 and over 6 million have been sold. The 10/22 is available in many different configurations, with the most popular being the carbine with a 18.5″ barrel.
The Ruger 10/22 is very easy to disassemble and reassemble, making it a great gun for beginners to learn on. In this article we will go over how to remove the barrel from a Ruger 10/22.
Before we begin, make sure the gun is unloaded and there is no magazine inserted. Also, make sure the gun is pointed in a safe direction.
- Remove the bolt by pulling it to the rear and then pressing the release lever located just above the trigger.
- Once the bolt is removed, pull the charging handle located on the right side of the gun all the way back and then release it.
- Next, locate the take down screw located on the underside of the gun just forward of the trigger guard. Use a coin or a flat head screwdriver to remove this screw.
- With the take down screw removed, you should now be able to pull the barrel assembly away from the receiver.
- The barrel can now be removed from the barrel assembly by pressing the release button located on the left side of the assembly and then sliding the barrel out.
And that’s it! You have now successfully removed the barrel from your Ruger 10/22.
What is a 10/22 Barrel and Why Should You Remove It?
A 10/22 barrel is the main component of the Ruger 10/22 rifle. It is a cylindrical tube that houses the firing mechanism and is made of stainless steel or alloy steel. It is attached to the receiver and the stock and is responsible for stabilizing the bullet when it is fired. Because the 10/22 barrel is the most important component of the rifle, it is important to remove it when cleaning or servicing the rifle. This ensures that the barrel is properly lubricated and free of debris that could affect the accuracy and performance of the firearm. Additionally, it is important to remove the 10/22 barrel when transporting the rifle in order to keep it secure and protect it from damage.
What Tools Are Needed to Remove a 10/22 Barrel?

The tools needed to remove a 10/22 barrel include a flathead screwdriver, a 3/8-inch wrench, a hex key, and a rubber or plastic mallet. The flathead screwdriver is used to loosen the barrel band screw, while the 3/8-inch wrench is used to loosen the barrel band nut. Next, the hex key is used to loosen the barrel nut, and finally a mallet is used to tap the barrel off of the receiver. It is important to remember to always wear safety glasses when performing any type of work on firearms.
Step-by-Step Guide to Removing a 10/22 Barrel.
To remove a 10/22 barrel, you’ll need a few tools including a screwdriver, a block of wood, a hammer, and a wrench. First, you’ll need to unscrew the barrel band located at the front of the barrel. Once the band is unscrewed, you’ll need to use the wrench to loosen the barrel from the receiver. Then, you’ll need to place the block of wood against the barrel and use the hammer to tap the barrel out of the receiver. Once the barrel is removed, you can clean it, replace it, or store it for future use.
Tips and Tricks to Make the Process Easier.
Removing a 10/22 barrel requires the use of a few specialized tools, but with the right preparation and knowledge, it can be done quickly and easily. Firstly, you’ll need to find a 10/22 barrel wrench that fits your specific barrel. Secondly, a good quality, solvent-resistant gun mat will help protect your work surface from potential damage. Then, use a screwdriver to remove the takedown screw located at the back of the receiver.
If necessary, you may also need to remove the forend and stock to access the takedown screw. Once the takedown screw is out, you will be able to pull the barrel off the receiver. Finally, use a solvent to clean the barrel and receiver, and then reassemble the rifle. Following these steps should make the process simpler and help you get the job done right.
Common Issues and How to Troubleshoot Them.
Removing the barrel of a 10/22 rifle is relatively straightforward. First, ensure the rifle is unloaded and the safety is engaged. Then, unscrew the receiver cap screw located near the rear sight, and carefully remove the receiver. Pull the barrel away from the receiver, and you should now have access to the barrel. To remove the barrel, loosen the barrel nut located at the front of the barrel until it can be unscrewed fully. Once the barrel nut is unscrewed, the barrel should come right off. Once the barrel has been removed, the rifle is now ready to be reassembled in the reverse order.
When Should You Consider Professional Services?
You are not familiar with the process of removing a 10/22 Barrel, it is highly advised that you seek the services of a professional gunsmith. This is especially true if you are unfamiliar with the specific make and model of the gun, as the process of removing the barrel can vary from model to model. Additionally, if you have any questions or concerns about the safety of the process, it is best to have a professional handle it. A certified gunsmith will have the know-how to properly and safely remove the barrel of your gun, ensuring that the job is done correctly.
Frequently Asked Questions [FAQs]
You will need a flat-head screwdriver, a Phillips head screwdriver, and a 3/8″ wrench.
First, remove the receiver cap by unscrewing it with a flat-head screwdriver. Next, remove the screws that hold the barrel in place with a Phillips head screwdriver. Finally, use a 3/8″ wrench to loosen the barrel nut and remove the barrel from the receiver.
No, you will need to remove the receiver cap in order to remove the barrel from the receiver.
No, the barrel nut needs to be removed in order to remove the barrel from the receiver.
If the barrel nut is stuck, you can try using a barrel nut wrench to loosen it. If the barrel nut wrench does not work, you may need to use a hammer to lightly tap the wrench until the barrel nut loosens.
Conclusion
To remove the 10/22 barrel, first remove the magazine and clear the chamber. Then, unscrew the front sight assembly and remove it. Next, unscrew the receiver cap and remove the bolt stop pin. With the pin removed, the bolt can now be pulled out of the receiver. Finally, unscrew the barrel from the receiver.
With the barrel removed, the 10/22 is now ready to be cleaned or repaired.

A. Wilcox Head is a lifelong shooter, hunter, and firearms enthusiast. Head grew up in a family where firearms were a way of life, and from an early age, he was taught the importance of firearm safety, accuracy, and proper hunting techniques.
1 thought on “How To Remove 10 22 Barrel”